• Home
  • Archive by category "Coolant Testing"

Category: Coolant Testing

Coolant Sample Testing in Islamabad, Pakistan

Posted by: Chemist Posted on: July 17, 2026

Enquiry:
We are looking for a laboratory to perform testing and analysis of a coolant sample. Kindly provide us with your quotation for testing the following parameters:

  1. Boiling Point
  2. Freezing Point
  3. Mono Ethylene Glycol (MEG) Ratio / Concentration
  4. Anti-Rust Agent
  5. Anti-Scaling Agent

Please also include the following information in your quotation:

  • Test methods/standards used
  • Sample quantity required
  • Turnaround time for the test results
  • Cost breakdown (if applicable)
  • Any other requirements for sample submission

We would appreciate receiving your quotation at your earliest convenience.

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Diesel, Lube Oil, and Coolant Analysis in Malaysia

Posted by: Chemist Posted on: January 17, 2025

Enquiry:

We are seeking quotations for laboratory testing services for Diesel Fuel, Lube Oil, and Coolant samples, as per the specifications outlined in the attached document. The testing will be conducted periodically over the next few years. We prefer the laboratory to be locally available in Malaysia to ensure efficient sample handling and timely results.

SCOPE OF WORK:

1. Lube Oil Analysis

a.  Required Tests: Viscosity at 100°C, Flash Point (COC & PM), Soot Content, Total Base Number (TBN), Water Content, Oxidation, Ethylene Glycol.

b. Methods: ASTM/DIN/ISO standards as specified in the attached document.

2. Coolant Analysis

a. Required Tests: Sum of Alkaline Metals (as CaCO₃), pH Value, Chloride Ions, Sulfate Ions, Anions Total (Cl, SO4), Bacteria, Yeast (Fungi and Mold), Silicon.

b. Methods: ICP, IC, and other relevant standards as specified.

3. Diesel Fuel Analysis

a. Required Tests: Total Contamination, Density at 15°C, API Gravity, Viscosity at 40°C, Flashpoint, Boiling Curve, Water Content, Carbon Residue, Oxide Ash, Sulfur Content, Cetane Number, Cetane Index, Copper Corrosion, Oxidation Stability, Lubricity, Neutralization Number.

b. Methods: ASTM/DIN/ISO standards as specified in the attached document.

SAMPLE DETAILS:

1. Frequency: Testing will be conducted every four months.

2. Sample Volume:

a. Diesel Oil: 6 samples x 1 liter each.

b. Coolant: 12 samples x 1 liter each (HT and LT lines).

c. Lube Oil: 6 samples x 1 liter each.

3. Additional Samples: A one-time sample of fresh coolant and lube oil for baseline parameter establishment.

KEY REQUIREMENTS:

a. Results must be provided in the units and measurement scale specified in the attached document.

b. Results must clearly indicate whether the readings fall within the allowed limit values.

c. Confirmation of lead time for receiving results after sample submission.

QUOTATION SUBMISSION:

Please provide your quotation, including:

a. Cost per test or package.

b. Total cost for the initial batch of samples.

c. Lead time for results.

d. Any additional terms or conditions.

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Drilling Oil, Gas, Water, Coolant Testing in Houston, TX

Posted by: Chemist Posted on: February 1, 2024

Enquiry:

I would appreciate it if you can answer my following questions:

As one of the most elite Drilling companies in the world and oil & gas companies, our maintenance routine has to align with our international maintenance standards program, which requires following an OIL ANALYSIS system requirement.

Currently we are working on a new big project for oil and gas company, due to our intensive maintenance program, we are required to have constant equipment monitoring system, which help us a lot to expect equipment failure and lower our down time / unproductive time.

our oil analysis requirements are for different types of Oil / Fluid Analysis (e.g. Hydraulic 32, 46, 68 – Transmission 160, 220 – Engine 15W40, Diesel Fuel, Radiator Coolant, Water…. etc.) so your service is highly required to proceed forward with our program, so upon all what had been mentioned above.

Kindly, reply accordingly to the following questions:

  1. Do you have an oil analysis system that we can use?
  2. If so, how can we start using your services immediately?
  3. If we got an agreement for your services, would we be responsible for delivering the samples for you, or you will collect it?
  4. Are you going to provide us the oil sample bottles and labels to be filled?  or we will have to provide all?
  5. If we have to provide it, do you recommend a specific brand, or color (e.g. Black to protect the sample from direct light)?
  6. How long would you recommend for oil sample from the time the sample is drawn to the time of delivery to your labs / facility?
  7. How long does it take to receive the oil analysis report from the time we deliver the sample?
  8. How much would it cost for your oil analysis service? is it per one oil analysis samples or it is per month or flat rate ?
  9. If we bought also the oil drums from your company, would we have a discount or free oil analysis? if so, please let us know the full details with some examples?
  10. Are your labs accrediting from any oil analysis organization / Quality organization bodies?
  11. Do you have a portable oil analysis machine (small oil lab analysis benchmark ) that we can purchase it and keep it permanently in our location?
  12. If so, how much would it cost to purchase it? And what is the Manufacture/ brand and the model? How long it will take to deliver it? How long it will to train one of our employees on it? is user friendly?
  13. Do you have a constant monitoring oil analysis device that can continuously monitor the oil condition? If so, what is the cost of it? And what is the Manufacture / brand, model?

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].