Diesel Sample Testing in Kuwait

Enquiry:

Can you confirm if Accredited labs can also perform ASTM D975 analysis of diesel sample that includes UOP46 testing for wax, ASTM D2500 and ASTM D6371 / IP309.

Please consider this as urgent. Your earliest response will be highly appreciated.

Once confirmed, please submit a quote and also advise the amount of diesel required to carry out these tests, along with estimated time for analysis and results.


One of our highly proficient and ISO certified laboratory would be taking over this testing.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Water Quality Testing in Singapore

Enquiry:

We are looking for accredited lab facility that can provide analysis of water quality parameters (e.g. pH, Chemical oxygen demand (COD), TSS, Iron, Manganese, Aluminium, Calcium, Total organic carbon (TOC), colour, Ammonia (NH3-N), Total Nitrogen and Total Phosphorus) based on the samples that we provide.

The samples would be as below.

i) supernatant from Gravity Sludge Thickners,

ii) supernatant from decant tank,

iii) filtrate from filter press

The samples will be collected from PUB plant and provided to you by us.

Please reply if your company able to provide such lab analysis services. If yes, we will discuss further on the level support required.


One of our highly proficient and ISO certified laboratory would be taking over this testing.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Chiller Oil Testing in India

Enquiry:

Mentioned below parameters need to check in chiller’s oil, we have total 6Nos. of chillers ( 4Nos. of 1000 TR & 2Nos. of 500TR), kindly share your quotations at the earliest.

Also confirm your NABL certifications.

Sr. No.TEST DESCRIPTION
1Kinematic Viscosity at 40 °C
Kinematic Viscosity at 100 °C
Viscosity Index
Total Acid Number
Water Content
Elemental  Analysis by ICP-AES
Aluminum Content
Barium Content
Boron Content
Calcium Content
Cadmium Content
Chromium Content
Copper Content
Iron Content
Lead Content
Lithium Content
Magnesium Content
Manganese Content
Molybdenum Content
Nickel Content
Phosphorous Content
Potassium Content
Sodium Content
Silver Content
Tin Content
cSt
cSt

mg KOH/g
mg/kg
mg/kg
mg/kg
mg/kg
mg/kg
mg/kg
mg/kg
mg/kg
mg/kg
mg/kg
mg/kg
mg/kg
mg/kg
mg/kg
mg/kg
mg/kg
mg/kg
mg/kg
mg/kg
mg/kg
mg/kg

One of our highly proficient and ISO certified laboratory would be taking over this testing.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Animal Food Testing, Virginia, USA

Enquiry:

I was wondering if your lab was able to perform tests on certain food items to identify if it is an animal by-product, or plant based? Recently were made aware of a dining establishment which may be deceptively serving meat products to vegan diners, and are looking to confirm if this is the case.


One of our highly proficient and ISO certified laboratory would be taking over this testing.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Gasoline Additives Test in Mexico

Enquiry:

Our product is a gasoline additive that we want to certify in Mexico, but the Mexican regulations ask us for laboratory analysis results of the ASTM 5598 and 5500 methods. I would like to know if you handle these methods.

As well as with the analyzes required in points H and I, which I detail below.

H. Copy of the results issued by a laboratory regarding the tests carried out on the Petgas Additive in accordance with the ASTM D5598 and ASTM D5500 methods in order to determine the amount of additive required in the gasoline, in accordance with the properties of the Petgas Additive .

To carry out the tests referred to in the previous paragraph, the laboratory must use gasoline produced or imported that meet the characteristics established in table 5.1 of NOM-016-CRE-2016, Specifications for the Quality of Petroleum Products.

In relation to the foregoing, the laboratory in charge of issuing the results of said tests must be accredited in terms of the Law on Metrology and Standardization or, in the case of a laboratory located abroad, it must comply with the following requirements:

(i) That it is accredited by an Accreditation Body that is a signatory to the Mutual Recognition Agreement for Testing Laboratories, the International Laboratory Accreditation Cooperation, the Asia-Pacific Laboratory Accreditation Cooperation, or the Inter-American Cooperation of Accreditation. (ii) That the accreditation referred to in the preceding paragraph is based on the international guideline ISO/IEC 17025:2005 “General requirements for the competence of Testing and calibration laboratories” or the one that replaces it, or on foreign standards that are consistent with the international standard in question. (iii) That the ASTM D5598 and ASTM D5500 test methods are within the scope of the accreditation referred to in section (ii) above.

Note: In case of using a foreign laboratory, it will be necessary to translate said results into Spanish with an expert translator.

I. Copy of the reports issued by the laboratory referred to in paragraph H above, evidencing that the Petgas Additive compounds and their addition to oil products do not represent a risk to the control systems of the consumption equipment or vehicles, nor is there any harmful effect on the health of the population and the environment. In the event that the Petgas Additive contains organometallic compounds, the Applicant Company must previously obtain a favorable technical opinion for its use from the Ministry of the Environment and Natural Resources.


One of our highly proficient and ISO certified laboratory would be taking over this testing.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Peanut Oil Testing in India

Enquiry:

we want to test my product peanut ois foe exports… give me a details like how much times it take and what all the test want to take an also need a details of price…… please contact us… thank you.


One of our highly proficient and ISO certified laboratory would be taking over this testing.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Treated Sewage Water Testing in Oman

Enquiry:

I am from Oman, I saw in your website that you have labs in Oman.

I need to test a treated sewage water against the below components, in order to use the water or not for agriculture applications: 

  1. Biochemical Oxygen Demand
  2. Chemical Oxygen Demand
  3. Total Suspended Solids
  4. Conductivity
  5. Sodium Absorption Ratio
  6. pH Value
  7. Aluminum
  8. Arsenic
  9. Barium
  10. Boron
  11. Beryllium
  12. Cadmium
  13. Chlorides
  14. Chromium
  15. Cobalt
  16. Copper
  17. Cyanides
  18. Fluorides
  19. Iron
  20. Lead
  21. Lithium
  22. Magnesium
  23. Manganese
  24. Mercury
  25. Molybdenum
  26. Nickel

27. Nitrate, Nitrogen (Ammonia) and Organic Nitrogen

28. Oil and Grease 

 29. Total Phenols 

  • Total Phosphorous 
    • Selenium
    • Sodium
    • Sulphate
    • Silver
    • Sulphides
    • Vanadium
    • Zinc
    • Fecal Coliforms
    • Viable Nematode

or any other extra parameters and analysis you run.

Where is your lab to deliver the sample?

What is the minimum quantity for the sample?

What will be the price?