• Home
  • Archive by category "Engine Oil Test"

Category: Engine Oil Test

Car Engine Oil Testing in Dubai, UAE

Posted by: Chemist Posted on: March 5, 2024

Enquiry:

Im currently in Dubai and i was looking for a laboratory that provide analysis for car engine oil to check the health condition of the vehicle. I was looking exactly something look like BLACKSTONE in US (that provide engine oil analysis) You will be able to help me with that? thank you so much.

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Engine Oil Testing in Korea

Posted by: Chemist Posted on: September 21, 2023

Enquiry:

we would like to use your lab in  Korea, in order to test & analyze some of our products,

namely “engine oils” as for following parameters:

 Product name  Mirax MX9 5W-40 A3/B4, SPPrice,  €
required testsMB Oxidation fresh? 
HTCBT ? 
MB HTCBT ? 
PDSC?  
MTU Deposit Test?  
PDSC ? 
Oxidation test (TOC level 2)?  
Microcoking test ? 
 
 Product name  Mirax MX9 5W-40 A3/B4, SPMETHOD (API)
required testsOxidation freshgasoline and diesel, volumetric oxidation in a flask, oil is stirred at 150 degrees C for 168 hours, the change in viscosity is measured. The test shows how much the viscosity characteristics change after oxidation.
HTCBT ASTM D6594
HTCBTIt’s the same test as standard HTCBT (ASTM D6594) but with the use of biofuel
PDSCASTM D6186
MTU Deposit TestDIN 51535 (MTV 5040)
Oxidation test (TOC level 2)D55 3099 
Microcoking testGFC Lu 27-A-13, 2018-03

We are looking forward to receiving your price indications , required quantities  and approx. execution time.

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Engine Oil Condition Analysis in Safat, Kuwait

Posted by: Chemist Posted on: February 15, 2023

Enquiry:

I am writing to seek your services in assisting us to do an engine oil condition analysis for our fleets based on below;

Please provide us with your office location and contact numbers in Kuwait for further discussion on the same.

  1. 12,000 km   – 3 samples
  2. 15,000 km   – 3 samples
  3. 18,000 km   – 3 samples

One of our highly proficient and ISO certified laboratory would be taking over this testing.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Engine Oil testing (Gas genset) in Oman

Posted by: Chemist Posted on: February 9, 2023

Enquiry:

We need to do engine oil testing. Pl find attached oil test method.

Viscosity at 100 °c (mm2/s) Total base number TBN (mgKOH/g) Total acid number, TAN (mgKOH/g) iph value Water (% by vol.) Glycol (mg/kg) Oxidation (A/cm) Nitration (A/cm) Wear elements (mg/kg): Iron (Fe) Lead (Pb) Aluminum (Al) Copper (Cu) Tin (Sn) Silicon (Si) Test method ASTM 0445 DIN 51562 ASTM 02896 ISO 3771 ASTM 0664 ASTM 07946 ASTM 06304 EN 12937 ISO 6296 ASTM 02982 DIN 51453 DIN 51453 DIN 51399-1/-2 Llmit values for Series 4000 Max. 17.5 Min. 11.5 Min. 2.5 and TBN > TAN max. new oil value +2.5 Min. 4 Max. 0.2 Max. 100 Max. 20 Max. 20 Max. 30 Max. 20 Max. 10 Max. 20 *** Max. 5 Max. 15* Llmit values for Series 400 New oil value +30 % ** New oil value -60 % ** On request from factory Min. 4 Max. 0.2 On request from factory Max. 30 Max.30 Max.50 Max. 30 Max. 20 Max.50 Max. 15 Max. 10 *

  • The limit value for the wear element Si only refers to natural gas operation.
  • * New oil value can be requested from the factory
  • * * During the 1st oil change (max. 3000 op. hrs.), the limit value is 50 ppm.
    Table 2: Limit values for used gas engine oils SAE 40
    Used-oil analysis
    The results of the oil analyses must be archived.

One of our highly proficient and ISO certified laboratory would be taking over this testing.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Oils and Water Testing Contract, Qatar

Posted by: Chemist Posted on: September 20, 2022

Enquiry:

Our core business is to be one of the most important shipbuilder of commercial and vessels that is also active in the conversion and ship repair sectors.

Our local branch Doha, is in charge to carry out the technical management of incoming ships, that we have built after an order placed by clients.

Vessels will call Doha with following schedule:

By end 2022,  3 ships

By end 2023, 5 ships

By end 2024, 6 ships

By end 2025, 7 ships 

We are now in position to contact the main local companies and establish point of contact for any unforeseen service that could be necessary.

For this reason we would ask you if you can assist us to provide some test, as attached, with below frequencies and types of test:

Lub oil Engine                  12 tests/year per ship  (sampling provided)

Hyd and lub oil                40 tests/year per ship (sampling provided)

Chilled water                    2 tests/year per ship (sampling provided)

Cooling water                  8 to 16 tests/year per ship (sampling provided)

One of our highly proficient and ISO certified laboratory would be taking over this testing.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].