• Home
  • Archive by category "Material Testing Enquiries"

Category: Material Testing Enquiries

Material Testing Enquiries

Asbestos Testing in Riyadh, KSA

Posted by: Chemist Posted on: August 8, 2026

Enquiry:

We would appreciate it if you could provide a price quote and additional information regarding asbestos analysis for samples taken from old fuel tanks at the airport in the Riyadh region (approximately 45 years old).

Please clarify the following points in your response:

1- Analysis cost: What is the price per sample?

2- Scope of service: Does the price include:

3- Site visit and sample collection by a qualified technician?

4- Laboratory analysis (e.g., PLM or TEM)?

5- Issuance of an official technical report detailing the results?

6- Timeline: What is the turnaround time for issuing the final report after sample collection?

7- Requirements: Are there specific prerequisites or safety protocols that need to be coordinated prior to the site visit?

We appreciate your cooperation and look forward to your reply.

Please accept our highest regards and appreciation.

السلام عليكم ورحمه الله وبركاته 

تحية طيبة 

ارجو تزويدنا بعرض سعر ومعلومات إضافية بشأن إجراء تحليل الأسبستوس (Asbestos Analysis) لعينات مستخرجة من خزانات وقود قديمة في المطار بمنطقة الرياض  (يعود عمرها إلى نحو 45 سنة).

يرجى توضيح النقاط التالية في ردكم:

1- تكلفة التحليل: كم سعر تحليل العينة الواحدة؟

2- نطاق الخدمة: هل السعر يشمل:

3- زيارة الموقع وسحب العينات بواسطة فني مختص؟

4-التحليل المخبري (مثل PLM أو TEM)؟

5- إصدار تقرير فني رسمي بالنتائج؟

6- المدة الزمنية: ما هي المدة المستغرقة لإصدار التقرير النهائي بعد أخذ العينات؟

7- المتطلبات: هل توجد اشتراطات معينة أو إجراءات سلامة محددة يلزم التنسيق بشأنها قبل زيارة الموقع؟

شاكرين لكم حسن تعاونكم، وننتظر ردكم الكريم.

وتقبلوا بقبول فائق الاحترام والتقدير،

TCLP Test for Beads Waste Disposal, Lahore, Pakistan

Posted by: Chemist Posted on: July 17, 2026

Enquiry:

We want to perform the TCLP test for the wastage of used aluminum oxide beads.

These beads are utilized for cleaning of metallic parts of turbocharger at beads blasting machine, pls check & share your quotation for this test.

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Testing of Wet Sieving of Dye ISO787-18 in Lahore, Pakistan

Posted by: Chemist Posted on: July 14, 2026

Enquiry:

TESTING OF WET SIEVING OF DYE – ISO 787/18

We intend to have Yellow Dye tested for Sieving (Wet) to check percentage (%) retained on 250 micron sieve by wet sieving process.

Please let us know whether you can conduct this test.

Please also share testing fee and time required.

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Slip Resistance Testing in Dammam, KSA

Posted by: Chemist Posted on: July 7, 2026

Enquiry:

One of our clients is looking for slip resistance testing at a site located in Jeddah.

Could you please confirm whether your company provides this testing service? If so, kindly contact me at your earliest convenience.

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Sand Testing in France, Europe

Posted by: Chemist Posted on: June 24, 2026

Enquiry:

We collected sand from seabed during cable repair operation. We observed some abbrasion on cable and it might be due to sand particles (we observed fine sand between armour wires of the cable). We would like to conduct a test to know the particles repartition & also a test to evaluate the “stifness” of the sand to comapre it to the cable. I don’t really know the tests you can provide to evaluate both characteristics. Could you please contact me to discuss about that ?

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Third Party Type Testing of HDPE DWC Pipe in Dubai, UAE

Posted by: Chemist Posted on: June 19, 2026

Enquiry:

We require a quotation for conducting Third-Party Type Testing of HDPE Double Wall Corrugated (DWC) Pipe, Size 40 mm OD / 32 mm ID, in accordance with IEC 61386-24.

Please provide your quotation for the following tests:

  1. Dimensional Verification (OD, ID, Wall Thickness)
  2. Compression Test
  3. Impact Resistance Test
  4. Bending Test at Room Temperature
  5. Bending Test at -5°C
  6. Resistance to Flame Propagation Test
  7. Glow Wire Test (750°C)
  8. IP67 Dust Ingress Test
  9. IP67 Water Ingress Test
  10. Anti-Rodent Test
  11. UV Resistance / UV Protection Test
  12. Raw Material Verification (Density & MFR/MFI)

Kindly provide:

  • Test charges
  • Sample quantity requirement
  • Lead time for testing
  • Accreditation details of the laboratory
  • Format of the Type Test Report

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

GRP Pipe Sample Analysis in Jubail, KSA

Posted by: Chemist Posted on: June 8, 2026

Enquiry:

GRP sample for lab Analysis

The purpose of this scope of work is to provide the service for Laboratory Analysis of
GRP samples from internationally certified company. The third-party service company will collect
the old GRP samples from different location and do the required Lab analysis as explained in the
Scope of work below.

1.1 The third-party company shall include following in the testing & failure analysis:
1.1.1 Visual Inspection as per ASTM D 2563.
1.1.2 Ignition-loss test as per ASTM D 2584.
1.1.3 Barcol Hardness as per ASTM D 2583.
1.1.4 Tensile testing ASTM D638
1.1.5 Axial Flexural Testing ASTM 0790
1.1.6 Hoop Tensile Test ASTM D 2290.
1.1. 7 Glass transition temperature ASTM D3418.
1.1.8 Stiffness, Ring Differential & Deflection test as per ASTM D 2412.
1.1.9 Optical Microscopy.
1.1.10 Scanning Electron Microscopy (SEM).
1.1.11 Engineering Evaluation of Data.
1.2 The testing and analysis shall be done to get the following details.
1.2.1 The root cause of failures.
1.2.2 The type of damage mechanisms.
1.2.3 The reliability assessment of piping materials deteriorations.
1.2.4 The remaining life assessment of existing GRP lines, based on lab analysis
1.2.5 Provide the recommendations to eliminate this kind of failure and prioritize
the short term & long-term recommendations.

    One of our highly proficient and ISO certified laboratory would be taking over this job.

    Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].