• Home
  • Archive by category "Pakistan"

Category: Pakistan

Pakistan

Regasified Liquified Natural Gas Testing in Lahore, Pakistan

Posted by: Chemist Posted on: October 9, 2026

Enquiry:
Kindly provide your quotation for RLNG (Regasified Liquefied Natural Gas) testing, with sample collection to be arranged at our Industries plant site.

The required testing parameters are as follows:

  1. Hydrocarbon Composition: Methane, Ethane, Propane, and other hydrocarbons.
  2. Nitrogen (N₂) Content
  3. Carbon Dioxide (CO₂) Content
  4. Total Sulphur Content

Please also confirm the following details:

Whether the report will include the individual gas composition percentages and total sulphur concentration.

Sample collection arrangements at the site, Thatta, Sindh.

Applicable testing methods and standards.

Sampling charges and total testing cost, including applicable taxes.

Required sampling conditions and any arrangements needed at the site.

Expected turnaround time (TAT).

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Lubricant Grease Testing in Jacobabad, Pakistan

Posted by: Chemist Posted on: September 20, 2026

Enquiry:

We are currently looking to conduct comprehensive laboratory testing on the industrial grease used in our electric motor maintenance routines at 50 Degree ambient Temp.

The primary objective of this testing is to evaluate the quality and performance parameters of the grease, verify its authenticity, and ensure its suitability for the electric motor bearings in our facility.

Could you please provide a detailed quotation and information regarding the testing services you offer for lubricating grease? Specifically, we would like to include the following parameters in the scope of testing:

1. Quality & Composition Analysis (e.g., Base Oil Viscosity, Dropping Point, Consistency / NLGI Grade, Penetration Test)

2. Authenticity & Identification (e.g., FTIR Spectroscopy / Compositional Fingerprinting)

3. Bearing Suitability & Mechanical Stability (e.g., Four-Ball Wear Test, Oil Separation, Corrosion Preventative Properties, Roll Stability)

Please include the following details in your quotation:

– Required sample quantity for the complete test

– Accreditations or standards followed (e.g., ASTM, ISO)

List of Grease available at our facility and bearings Used in Motors is attached.

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Annual Contract Transformer Oil Testing in Ghotki, Pakistan

Posted by: Chemist Posted on: September 14, 2026

Enquiry:

We would like to conduct transformer oil testing as per the below-mentioned tests. Kindly provide your quotation.

Your early response will be highly appreciated.

Annual 3rd Party Transformer Oil Testing

A)Transformer’s oil DGA as per ASTM D 3612 and IEC 60567 for following key gases (06 Samples)

1) Hydrogen.

2) Oxygen.

3) Nitrogen

4) Methane

5) Carbon Monoxide

6) Ethane

7) Carbon Dioxide

8) Ethylene

9) Acetylene

B) Water Content, D1533 IEC 60814  with relative saturation (06 Samples)

C) Dielectric BDV, IEC 60156 (06 Samples)

D) Furanic Compounds in Oil/ Paper Degradation (06 Samples)

E) Acidity, IEC 62021 (06 Samples)

F) Dissipation Factor @ 90°C, IEC 60247 (06 Samples)

G) Inhibitor Content, IEC 60666 (06 Samples)

H) Sulfur-Potentially Corrosive, IEC 62535 (06 Samples)

I) Passivator in Oil, IEC 60666 (06 Samples)

J) Methanol and Ethanol, Doble (06 Samples)

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Industrial Gas Meters Calibration in Pakistan

Posted by: Chemist Posted on: September 10, 2026

Enquiry:

Subject: itron gas meters Message Body:
Need quote for calibration of “Itron” industrial gas meters. Following details.
Connection Sizes: 2 inches, in and out
Calibration Points: 1 point
Application: Sui Gas
No. of meters:
G40: 2
G75: 4

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Commodity of Rice Testing in Karachi, Pakistan

Posted by: Chemist Posted on: September 9, 2026

Enquiry:
We request you to please advise us
the charges for the following Lab Test for the requirement of Government of Pakistan Ministry of
National Food Security & Research Department of Plant Protection for Export of Pakistani Rice.,

Required Test Detail:
– MRL,
– Mycotoxin,
– Heavy Metal,

And also advise us how many days you have to issue a Lab Report after receiving the sample, and you
share the Lab Test Report Via Email or WhatsApp and also inform us your representative will collect
the sample from our office at S.I.T.E, Karachi or we will send you the sample.

Also inform us that your firm is approved by the Department of Plant Protection Government of Pakistan Karachi and

your test report acceptable for issuance of Phytosanitary Certificate for Export of RICE..

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Associate Business Partnership – Labs and Surveyors

Posted by: Chemist Posted on: September 7, 2026

ASSOCIATE BUSINESS PARTNERSHIP

Get Direct Customer Enquiries — Not Just Leads

Partner with us to receive genuine customer enquiries directly, helping you reduce the significant costs associated with Internet Marketing and SEO.

Grow Your Business • Reduce Marketing Costs • Reach More Potential Customers

Capture valuable business opportunities online that are currently being secured by your competitors and larger industry players.

Partner With Us & Turn Online Enquiries Into Real Business

More details -> PARTNERSHIP AGREEMENT

Barrage Gate Rubber Seal Testing, Witnessing in Pakistan

Posted by: Chemist Posted on: September 4, 2026

Enquiry:
Kindly confirm whether your laboratory can provide the required testing and witnessing facilities for barrage gate rubber seals, including Hardness, Tensile Strength, Elongation at Break, Water Absorption, and Compression, along with the applicable standards and test methodology.

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].