Accredited Test Labs Inspection, Testing, Calibration Services.

Settled Sludge Sample Testing in Jubail, KSA

Posted by: Chemist Posted on: October 22, 2026

Enquiry:

Our company invites your laboratory to submit a technical and commercial proposal for the analysis of a bottom settled sludge sample collected from POND-I at our facility.

The objective of this study is to fully characterize the sludge composition and determine the purity and percentage of Sodium Sulphate (Na₂SO₄) through a two-stage analysis, including:

Full characterization of liquid and solid phases
Hydrocarbon, BTX, VOC, TOC, COD, pH, metals, and metal salts analysis
Advanced pretreatment to remove water and hydrocarbons
Dry mineral matrix analysis for Sodium Sulphate quantification
Complete mass balance calculations and Certificate of Analysis (COA)

Please find the attached Scope of Work for your review.

Kindly confirm your laboratory’s capability to perform the required separation, pretreatment, and analytical procedures, and provide the following:

Technical proposal and methodology
Accreditation details (ISO 17025 or equivalent)
Estimated turnaround time
Commercial quotation
Sample quantity requirements, if any

We would appreciate receiving your quotation at most of your convenience time.

KINDLY ACKNOWLEDGE RECEIPT OF THIS EMAIL BY A REPLY

Should you require any clarification, please feel free to contact the undersigned.

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Water Testing as per RCJ Compliance in Jubail, KSA

Posted by: Chemist Posted on: October 10, 2026

Enquiry:

I am reaching out to inquire about your analytical testing capabilities for water and wastewater samples. We need to conduct testing for a specific suite of parameters, and it is critical that the methods and reporting fully comply with the Royal Commission of Jubail (RCJ) requirements.

Below are the parameters required in the test report:

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Contract for 15 Vessels Fleet Oil, Foam, Water Testing in Jubail, KSA

Posted by: Chemist Posted on: October 4, 2026

Enquiry:

Periodic Lab Contract for Lube Oil, MGO, Fuel Oil, FF Foam, Fresh Water, Ballast Water Testing

As we are currently reviewing our laboratory service requirements and inviting selected vendors to submit their commercial proposals, we would like to initiate a formal rate contract with your Lab for the approximately 14-15 vessels we currently manage in KSA .

Kindly provide us with your best and most competitive rate proposal for the below requirements so that we can review the same and proceed towards establishing a formal agreement with your Lab.

For products having Sulphur content less than 500 ppm then the standard recommends to do “lubricity” test according to ISO 12156 method & the cost related to this to be provoided seperately in addition to the above-mentioned charges.

Kindly also provide your quote basis the below :

Fuel Oil Analysis as per RMG/ RME –ISO 8217: 2017 Spec

Foam Analysis -Basic Test/Parameters ref below

Foam Analysis (With Fire test and Chemical Stability) ref below

– Foam Concentration Test ref below

Please note the following PO arrangements:

Pos will be issued from our Shipworkz Dubai office . 15% VAT to be added as well during invoicing

For each analysis/service included in your proposal, kindly clearly specify:

Sample quantity required for each analysis.
Turnaround time – number of days required to complete the analysis and issue the report after receipt of the sample at your laboratory. Samples to be collected from our office located at Jubail.
Free sampling bottles to be provided, including secure lids/caps and appropriate labels.

Expected Sampling Frequency

Please consider the anticipated volume of samples based on the following frequency:

Main engine and auxiliary engine lube oil: Analysis every 3 months.
Other equipment: Analysis every 6 months.

We would appreciate your best commercial rates, taking into consideration the anticipated volume of samples and our intention to establish a long-term business relationship with us.

Please treat the proposed rates and commercial information as strictly confidential and kindly refrain from forwarding or copying this communication to any internal or external stakeholder without our prior consent.

Should you have any questions or require further clarification regarding the scope, please feel free to contact me directly.

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Filter Plan Drinking Water Testing in Jubail, KSA

Posted by: Chemist Posted on: October 3, 2026

Enquiry:

We would like to enquire about third-party laboratory testing and approval of drinking water produced from our newly installed water treatment plant at Plant.

The water treatment plant is ready for use; however, prior to using the treated water for drinking purposes, we understand that the water should be tested by an approved/accredited third-party laboratory to verify that it meets the applicable drinking-water quality standards.

Kindly provide us with your quotation and details for the required testing, including:

Required water quality tests and parameters
Applicable drinking-water standards/specifications
Sampling procedure and number of samples required
Laboratory accreditation/approval details
Testing charges
Expected turnaround time for the test report
Validity or renewal requirements, if applicable
Any certificates or documents required from our side

Please also advise whether your team can arrange on-site water sampling at Abu Hadriya Camp and issue an official laboratory test report/certificate confirming the suitability of the treated water for drinking purposes.

Kindly submit your commercial offer along with the scope of testing at your earliest convenience.

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Hydraulic Oil Testing in Jubail, KSA

Posted by: Chemist Posted on: September 20, 2026

Enquiry:

Service for Hydraulic Oil Laboratory Analysis,
The Oil analysis Parameters are as follows:

NAS 1638 Class / ISO 4406: To measure solid particle contamination
and
micro-debris.
Water Percentage / Moisture Content: To detect dissolved water or
moisture in the oil.
Total Acid Number (TAN): To check for fluid oxidation and acidity
levels.
Kinematic Viscosity @ 40°C: To verify if the oil still retains its
original ISO VG 68 thickness.
Total 12 Nos. Samples for Lab Analysis.

P.T. Power pack # 04

Crimping Press

U Press

O Press

U <(>&<)> O Press Auxiliary system

CTW

Expander

Hydro Tester

End Facer # 02

P.T. Power pack # 01

P.T. Power pack # 02

P.T. Power pack # 03

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Water Samples Testing in Jubail, KSA

Posted by: Chemist Posted on: September 16, 2026

Enquiry:

Please find below the list of water sampling analysis parameters with methods for your review.

We kindly requesting your support in providing a quotation with reasonable pricing, with other terms & condition.

I would like to thanks and appreciate it if you could respond at your earliest convenience.

Thank you for your assistance, and we look forward to your reply.

S #	Parameters	USEPA Method	Reagent
1	Hydrogen Chloride (HCl)	USEPA 26/26A	0.1N H₂SO₄
2	Hydrogen Fluoride (HF)	USEPA 26/26A
3	Ammonia (NH₃)	SCAQMD 207.1
4	Metals (As, Ag, Ba, Be, Cd, Cr, Co, Cu, Pb, Mn, Ni, Hg, Tl, V, Sb)	USEPA 29	5% HNO₃ / 10% H₂O₂
4		USEPA 29	4% KMnO₄ /10% H₂SO₄
5	Hydrogen Sulphide (H₂S)	USEPA 11	3% H₂O₂
5	Hydrogen Sulphide (H₂S)	USEPA 11	CdSO₄
6	Sulfuric Acid Mist (including SO₃)	USEPA 8	80% isopropanol
7	Formaldehyde (HCHO)	USEPA 316	DI Water

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Water Testing Annual Contract Dammam, Jubail, Aziziya, KSA

Posted by: Chemist Posted on: July 20, 2026

Enquiry:

Request for Quotation – Annual Water Testing Services

We have a requirement for annual water quality testing services in Aziziya, Dammam, and Jubail.

The scope includes:

• Monthly sampling for treated water and swimming pool water (where

applicable).

• Separate Microbiological (Bacterial) and Chemical analyses.

• Total requirement: 60 sampling events per year (36 for Aziziya, 12

for Dammam, and 12 for Jubail).

Kindly provide your best quotation for this requirement, including:

• Unit rates for Microbiological (Bacterial) Analysis

• Unit rates for Chemical Analysis

• Any sample collection/transportation charges (if applicable)

• Report turnaround time

• Validity of the quotation

Please share your quotation at your earliest convenience.

If you require the detailed list of testing parameters, please let us know and we will share the complete scope.

Thank you, and we look forward to your prompt response.

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

GRP Pipe Sample Analysis in Jubail, KSA

Posted by: Chemist Posted on: June 8, 2026

Enquiry:

GRP sample for lab Analysis

The purpose of this scope of work is to provide the service for Laboratory Analysis of
GRP samples from internationally certified company. The third-party service company will collect
the old GRP samples from different location and do the required Lab analysis as explained in the
Scope of work below.

1.1 The third-party company shall include following in the testing & failure analysis:
1.1.1 Visual Inspection as per ASTM D 2563.
1.1.2 Ignition-loss test as per ASTM D 2584.
1.1.3 Barcol Hardness as per ASTM D 2583.
1.1.4 Tensile testing ASTM D638
1.1.5 Axial Flexural Testing ASTM 0790
1.1.6 Hoop Tensile Test ASTM D 2290.
1.1. 7 Glass transition temperature ASTM D3418.
1.1.8 Stiffness, Ring Differential & Deflection test as per ASTM D 2412.
1.1.9 Optical Microscopy.
1.1.10 Scanning Electron Microscopy (SEM).
1.1.11 Engineering Evaluation of Data.
1.2 The testing and analysis shall be done to get the following details.
1.2.1 The root cause of failures.
1.2.2 The type of damage mechanisms.
1.2.3 The reliability assessment of piping materials deteriorations.
1.2.4 The remaining life assessment of existing GRP lines, based on lab analysis
1.2.5 Provide the recommendations to eliminate this kind of failure and prioritize
the short term & long-term recommendations.

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Molten Zinc Analysis in Jubail, KSA

Posted by: Chemist Posted on: May 10, 2026

Enquiry:

We would like to request your urgent quotation for Molten Zinc Chemical Analysis as per

our approved Purchase Requisition for our Galvanizing Plant Quality Control requirements.

Service Details

Service: Molten Zinc Analysis
Description: Chemical analysis of molten zinc bath
Quantity: 1 Set
Frequency: Monthly (May 2026)
Department: QC – Galvanizing
Client / Facility: Al‑Jubail

Scope of Analysis

Kindly confirm analysis covering (but not limited to):

Zn %
Al %
Fe %
Pb %
Other trace elements as per galvanizing standards

Kindly Include in Your Quotation

Price per analysis (set)
Test method / standard followed (ASTM / ISO, etc.)
Turnaround time for results : Immediately
Validity of quotation
Payment terms : As per Agreed Vendor Payment Terms
Sample submission requirements
Accreditation details (if available)
Quotation reference number

⚠️ This RFQ is urgent as it supports ongoing galvanizing quality control activities.
We would appreciate receiving your best quotation and earliest turnaround time at the soonest possible.

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Drinking Water Testing in Jubail, KSA

Posted by: Chemist Posted on: February 8, 2026

Enquiry:

Please provide us your best price for the supply of the items/service as per attached RFQ# Drinking water testing

We shall be expecting your quotation ASAP

Other terms and condition as follow:

1. Offer Validity to be mentioned in quotation clearly.

2. Indicate lead time

3. State standard packaging (if required)

5. Your payment term should be clearly mentioned

4. Indicate Shipping term

6. Indicate above mentioned RFQ number in your quotation/offer.

7. Delivery Location: JUBAIL PLANT

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].