I am reaching out to inquire about your analytical testing capabilities for water and wastewater samples. We need to conduct testing for a specific suite of parameters, and it is critical that the methods and reporting fully comply with the Royal Commission of Jubail (RCJ) requirements.
Below are the parameters required in the test report:
One of our highly proficient and ISO certified laboratory would be taking over this job.
Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].
We are currently looking for a company/laboratory to conduct water quality testing for our facility.
Kindly advise us on the procedure for collecting and submitting the water samples for testing, including whether the samples will be collected by your team or need to be provided by us.
Please also share the following information:
Available water testing packages and parameters
Sampling and testing procedure
Cost of the testing services
Estimated time required to receive the test results
Laboratory accreditation/certification details
Format of the final water quality test report
Kindly share your quotation along with the relevant details so that we can review and proceed accordingly. We look forward to your prompt response.
One of our highly proficient and ISO certified laboratory would be taking over this job.
Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].
Periodic Lab Contract for Lube Oil, MGO, Fuel Oil, FF Foam, Fresh Water, Ballast Water Testing
As we are currently reviewing our laboratory service requirements and inviting selected vendors to submit their commercial proposals, we would like to initiate a formal rate contract with your Lab for the approximately 14-15 vessels we currently manage in KSA .
Kindly provide us with your best and most competitive rate proposal for the below requirements so that we can review the same and proceed towards establishing a formal agreement with your Lab.
For products having Sulphur content less than 500 ppm then the standard recommends to do “lubricity” test according to ISO 12156 method & the cost related to this to be provoided seperately in addition to the above-mentioned charges.
Kindly also provide your quote basis the below :
Fuel Oil Analysis as per RMG/ RME –ISO 8217: 2017 Spec
Foam Analysis -Basic Test/Parameters ref below
Foam Analysis (With Fire test and Chemical Stability) ref below
– Foam Concentration Test ref below
Please note the following PO arrangements:
Pos will be issued from our Shipworkz Dubai office . 15% VAT to be added as well during invoicing
For each analysis/service included in your proposal, kindly clearly specify:
Sample quantity required for each analysis.
Turnaround time – number of days required to complete the analysis and issue the report after receipt of the sample at your laboratory. Samples to be collected from our office located at Jubail.
Free sampling bottles to be provided, including secure lids/caps and appropriate labels.
Expected Sampling Frequency
Please consider the anticipated volume of samples based on the following frequency:
Main engine and auxiliary engine lube oil: Analysis every 3 months.
Other equipment: Analysis every 6 months.
We would appreciate your best commercial rates, taking into consideration the anticipated volume of samples and our intention to establish a long-term business relationship with us.
Please treat the proposed rates and commercial information as strictly confidential and kindly refrain from forwarding or copying this communication to any internal or external stakeholder without our prior consent.
Should you have any questions or require further clarification regarding the scope, please feel free to contact me directly.
One of our highly proficient and ISO certified laboratory would be taking over this job.
Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].
We would like to enquire about third-party laboratory testing and approval of drinking water produced from our newly installed water treatment plant at Plant.
The water treatment plant is ready for use; however, prior to using the treated water for drinking purposes, we understand that the water should be tested by an approved/accredited third-party laboratory to verify that it meets the applicable drinking-water quality standards.
Kindly provide us with your quotation and details for the required testing, including:
Any certificates or documents required from our side
Please also advise whether your team can arrange on-site water sampling at Abu Hadriya Camp and issue an official laboratory test report/certificate confirming the suitability of the treated water for drinking purposes.
Kindly submit your commercial offer along with the scope of testing at your earliest convenience.
One of our highly proficient and ISO certified laboratory would be taking over this job.
Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].
VGP and IMO D2 Ballast Water Testing – BWTS System Calibration
We are the owner and management company of subject vessel . We kindly request your pr quotation for the BWTS (Ballast Water Treatment System) VGP&IMO D2 water analysis and calibrations of our vessel.
The vessel is scheduled to load in Houston around October 9-10.
One of our highly proficient and ISO certified laboratory would be taking over this job.
Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].
We are currently seeking a budgetary quotation for the subject requirement. Please find the attached Scope of Work (SOW) for your review.
Kindly note that the bid closing date and time is 22 September 2026 at 11:00 AM.
SOW:.
1. Purpose The subcontractor shall perform a complete inspection, testing, and condition assessment of the Central Chilled Water Plant (CWP) to evaluate the operational condition of eight (8) water cooled Chillers, each having capacity of 1100 TR and identify the extent of overhaul, repair, replacement, and maintenance activities required to restore the plant to reliable and efficient operation. 2. Scope of Services The subcontractor shall provide all necessary manpower, supervision, tools, instruments, testing equipment, consumables, transportation, and documentation required to execute the inspection.
2.1 Plant Survey and Data Collection
2.2 Chillers Inspection
Testing Requirements
Deliverables The subcontractor shall submit the following: 4.1 Inspection Report 4.2 Overhaul Recommendation Report 4.3 Final Assessment Matrix
HSE Requirements
Exclusions
Completion
One of our highly proficient and ISO certified laboratory would be taking over this job.
Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].
