• Home
  • Archive by category "Chemical Analysis"

Category: Chemical Analysis

Chemical Filtration and Analysis in Algeria, North Africa

Posted by: Chemist Posted on: September 2, 2026

Enquiry:

We are looking for Algeria local provider able to support us on chemical (liquid) filtration and lab analyses.

The filtration needed is for physical separation of suspended solids and involve large chemical quantity (over 1000 drums of 200L each). Objective is to remove suspension solids and pack the chemicals back into the drums (sealed).  

For laboratory analyses, we need:

  • Specific Gravity measurements
  • pH
  • Centrifugal solids 

So pls if you are doing this service pls to advise

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Chemical Raw Material Testing in KSA

Posted by: Chemist Posted on: August 18, 2026

Enquiry:
We are currently using 18 different chemical raw materials in our production. As part of our quality control process, we would like to conduct regular testing of these raw materials to verify their quality and ensure they meet the required specifications.

Kindly share your quotation for collecting the samples from our factory and conducting the required laboratory testing.

Please let me know if you require the chemical names, to prepare the quotation.

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Chemical Compatibility Testing Demulsifier Inhibitors Khafji, KSA

Posted by: Chemist Posted on: July 19, 2026

Enquiry:

We are requesting technical and commercial proposals from qualified laboratories to conduct Chemical Compatibility Testing between production Demulsifiers and Corrosion Inhibitors. Our demulsifiers and inhibitors are the following:

  • Corrosion Inhibitors
  1. CRW22051
  2. CRW22529
  • Demulsifiers
  1. DMO22758
  2. PHASETREAT 19745
  3. MC MX 1-6000
  4. Duradem 3901

The objective of this study is to evaluate potential incompatible interactions between these surface-active chemicals to prevent emulsion stabilization, foaming, or degradation of corrosion mitigation efficiency within production facilities.

1. Scope of Work

The selected laboratory will be required to perform the following evaluations using representative fluid samples provided by –:

  1. Physical Compatibility / Blend Testing: Visual assessment of neat chemical blends at varying ratios to check for precipitation, turbidity, or phase separation.
  2. Emulsion Bottle Testing: Bench-scale evaluation at simulated field temperatures to measure water drop rate, interface clarity, and residual BS&W across various chemical dosage matrices.
  3. Corrosion Efficiency Testing: Linear Polarization Resistance (LPR) or Electrochemical Impedance Spectroscopy (EIS) to confirm that the demulsifier does not degrade the protective film efficiency of the corrosion inhibitor.

2. Technical Data & Field Conditions (Approximate)

  1. Fluid Matrix: Crude Oil (~27–28° API), High-Salinity Produced Water
  2. Average Water Cut: 28% to 32%
  3. Operating Temperature: 38°C to 64°C
  4. Chemical Types: MSDS attached.
  • Submission Requirements

Please include the following details in your formal proposal:

  1. Technical Proposal: Detailed testing methodology, equipment specifications, applicable ASTM/NACE standards, and standard fluid volume requirements.
  2. Commercial Proposal: Itemized cost breakdown per test/matrix run and total project cost.
  3. Timeline: Estimated turnaround time from sample receipt to final report delivery.
  4. Qualifications: Key laboratory accreditations (such as ISO 17025) and relevant experience with GCC fluid systems.

We look forward to receiving your proposal.

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Coolant Sample Testing in Islamabad, Pakistan

Posted by: Chemist Posted on: July 17, 2026

Enquiry:
We are looking for a laboratory to perform testing and analysis of a coolant sample. Kindly provide us with your quotation for testing the following parameters:

  1. Boiling Point
  2. Freezing Point
  3. Mono Ethylene Glycol (MEG) Ratio / Concentration
  4. Anti-Rust Agent
  5. Anti-Scaling Agent

Please also include the following information in your quotation:

  • Test methods/standards used
  • Sample quantity required
  • Turnaround time for the test results
  • Cost breakdown (if applicable)
  • Any other requirements for sample submission

We would appreciate receiving your quotation at your earliest convenience.

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

ACP Fire Rating Testing in UAE

Posted by: Chemist Posted on: July 7, 2026

Enquiry:

We require a proposal for fire rating testing of 1 no ACP panel to check whether ACP is fire rated or not.

Please address proposal to,

To: community management

Attention: ——

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Calcium Carbonate Powder Testing in Qatar

Posted by: Chemist Posted on: June 25, 2026

Enquiry:

Need to undergo physical and chemical properties laboratory test for calcium carbonate powder

Message:

Physical Properties:-

1.D50 and D97 Particle Size Analyser in microns through malvern particle analyser.

2.Brightness and Whiteness of material

3.Material Hardness

4.Specific Gravity/Density

5.Oil Absorption

6.Ph value of material

Chemical Properties:-

1.Tota Caco3 percentage for purity test

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

1-MCP Testing 1.3% in Solution Generate CoA in Wapato, WA

Posted by: Chemist Posted on: June 24, 2026

Enquiry:

It appears that your lab is able to perform accredited testing of 1-MCP samples and generate CoAs? We’re looking to have a liquid sample of 1-MCP, encapsulated with a-cyclodextrin at ~1.3wt% in a matrix of salt and water tested. Is this something you would be able to help us out with or could you offer guidance on where we could look?

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].

Detergent Foam Performance Testing in Selangor, Malaysia

Posted by: Chemist Posted on: June 22, 2026

Enquiry:

We are manufacturer of specialty detergents for the semiconductor, electronics, and precision cleaning industries. Our facility is located at Berjaya Park, Shah Alam, Selangor, Malaysia.

We are currently looking for a laboratory or testing service provider that offers detergent foaming performance testing. We would appreciate it if you could provide information regarding:

  1. The foaming test methods available for detergent products.
  2. The testing standards or procedures used (e.g., ASTM, ISO, or other recognized methods).
  3. The sample quantity required for testing.
  4. The testing lead time.
  5. The applicable testing charges.

Kindly let us know the testing methodology that would be used to evaluate detergent foaming characteristics.

One of our highly proficient and ISO certified laboratory would be taking over this job.

Should you have any similar requisites, do drop us email and we shall revert instantly -> [email protected].